1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest

1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest
1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest
1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest
1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest
1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest
1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest

1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest

3 Directions Micro-adjustable Vacuum Screen Printer---16" x 20 ". Also suitable for all kinds of transfer paper, PVC, PET, PC and other soft/ hard film, board, paper, nameplate, and similar materials. It can also be used for the fine printing on heavy and thick products, such as paper boxes, glass, wood boards, metal plates, signage, various plastic boards and etc. Not suitable for cloth, ribbons, handkerchiefs and other textile products, textile materials are recommended to use the scraping pallet with glue.

1, The printing object can be tightly adsorbed on the pallet, to prevent the printing object moved by outside force. After printing, vacuum pallet can keep the printing object close to the pallet can won't be lift up by ink. Equip with 3 gravity balance plates, they can be installed individually or together according to weight request, it can be moved forward and back within 4 inches (10cm). With the bolt in the balance rack, could adjust the lifting angle and height of the screen frame.

This screen printing table uses 2 mm stainless steel plate laser cutting, table area is 40x50 cm; Vacuum area is 42x31.5 cm; Suction hole diameter is 1 mm; The spacing of air holes is 15 mm. The quantity of air holes are 638 (22 rows in horizontal direction and 29 rows in vertical direction).

Three-directions micro adjustable, it can be micro adjusted through the knob up and down, forward and back 3/4 inch, left and right 3/4 inch. Place the substrate on the table surface and start the vacuum pump. Clamp the screen frame after aligning the screen pattern with the substrate.

Height adjustment: place the screen frame flat on the platform. According to the substrate height or printing requirements, rotate the up and down adjustment handle to reach the appropriate height, and lock the height through the two rear positioning handles.

Left and right adjustment: loosen the handle on both sides of the nose, and rotate the handle to move slightly left and right as required; When it is done, tighten both handles. Back and forward adjustment: first, slightly loosen the four red knobs on the front of the chuck, then loosen the fine-tuning knobs on both sides of the front of the chuck and make front and rear fine-tuning as required. After the fine-tuning, tighten the knob and tighten the four red knobs on the top of the chuck. When substrate area is too small, adsorption will reduce, you can cover the blowholes around the substrate with plastic sheets or paper to increase the adsorption of substrate.

Clamp size: clamp size: 11.5" x 3", max thickness: 2. Suggest max screen frame size: 15.7x19.6x2 inches (40x50x5 cm). Suggest printing area: 11.8" x 15.7" (30x40 cm).

Machine size: 25.5x 15.7x 15.7 inches (65x40x40 cm). Stander height : about 6 inches. 1 set 16"x20" Three Directions Micro-adjustable Vacuum Screen Printer---006155. This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Screen Printing".

The seller is "favoritecoss39" and is located in this country: US. This item can be shipped to United States.


1pc Micro-adjustable 3-Direction Vacumm Screen Printing Press 16 x 20 Newest


Screen Printing Press    Sitemap    Contact Form    Privacy Policy    Service Agreement